Over time, a house will definitely need repairs in several areas. Some tips and tricks in this article hopefully can help you to renovate a house.
Stay Bright Without Dismantling the Roof
The corner of the room inside the house is usually dark. If you want to make this corner look bright, this is the solution without having to dismantle the roof structure.
Replacing Solid Roof with Transparent Roof
This method can be applied to buildings that use tile roofs or metal roofs. In principle, use a transparent roof of the same type with a solid roof around it. This is to prevent small gaps due to the mismatch of roof designs.
See also: Roof Tile Installation Procedure and Roofing Accessories Function
Create an Opening on the Wall
This is one solution that is quite effective for flowing the light into the room. To make the room bright, create a large or wide opening, reaching a minimum of a quarter of the wall. These openings can be spread in several places.
Installing Solar Light Tubes
This method is the latest method that is quite effective. The method is to use the Velux System’s light tube technology. Solar light tubes are installed on the roof. With this light tube, the sunlight is sent to openings in the ceiling. These light tubes solar can carry 99% of sunlight.
Walls Free from Damp
- To prevent damp walls, make a wall with a trassram as high as 120 cm. Trassram is a mortar made from a mixture of sand and cement in a ratio of 1: 3
- To prevent dampness for the wall that has already been built, use waterproofing to coat the wall.
How to Fix Hairline Crack in Concrete Decks
If there are indications of hairline cracks in concrete decks, do the following. Check the entire deck surface. Check how many areas are cracked. Repair large cracks by covering it using instant cement (mortar). Cover the entire deck surface using polymer-based waterproofing, which is available in a variety of color choices. Make sure the entire surface of the floor is protected and the cracks are tightly closed.
Carefully Using Recycling Wood
- To coat the walls, you can use recycled wood. To get an attractive appearance, you can play a wooden pattern, either in the form of lumber or raw wood.
- Although the price of recycled wood tends to be cheap, you have to be smart in choosing it. Choose the wood that is still dry, not moldy and notice the log straightness. Now, in the market there is a special tool that can check the level of wood dryness, wood moisture meter.
Repairing Uneven Walls
Uneven walls can be made smooth again. The first step, peel off the paint layer on the wall using a putty knife until you see the plaster surface. Clean the dust and the remaining layer of paint so as not to reduce the adhesive strength of the cement plaster that will be affixed to the wall. Wet the wall with water so there is no hairline crack when doing the plaster process. Plaster using cement mixed with additives or instant cement. Use plaster trowel melamine for maximum results. As an alternative so that the appearance of the wall looks more perfect, you can use a mixture of construction glue and calcium as wall spackle. After the wall surface dries, do repainting.
Installing Ceramic Gutter
Water seepage from the roof top becomes an integral part when there is a leak. The water will seep into the sagging gutters or gutters with holes. Gutters are often a vulnerable part of the damage. One alternative to be safer is to use ceramic gutters for ceramic roofs. Following are the steps for installing ceramic gutters.
Prepare a stand for the valley rafter. Mount the rafter beam parallel or lower than the purlin height. Attach 2 cm x 18 cm gutter board with 2 pieces. Then install the gutter cover material in the form of zinc or gutter carpet. Install the ceramic rafter from the bottom area to the upper area with overlap according to the design. Then do the nailing process from the bottom gutters to the valley rafter gutters. Finally, install roof tiles around it.
Prevent Leaks from Roofs and Walls
When building a house, sometimes there are gaps in the roof and walls that were unknown from the beginning. Later, this gap will bring problems to your home, which is leaking. For prevention, take the appropriate steps when the house building process is being carried out. After the roof tile is installed, give an additional layer on the roof tile on the side of the wall. This layer is a waterproof cement mixture, with a composition of 1: 2 (1 cement mixed with 2 grains of sand). The cement layer is applied overlapping 5 cm – 6 cm from the side of the wall. Then coat it again with a waterproof plaster. The following are the steps in the process.
See also: Asphalt Shingles or Bitumen Roof: Roof Material Types That You Should Know
Clean the intersection between the roof and the wall from dust and dirt. Also, make sure the roof tile and wall are not wet or damp conditions. Measure and cut the waterproof plaster according to the length of the intersection area between the wall and the roof to be closed. Attach the plaster until the gap is perfectly covered, half the width of the plaster attaches to the roof tile, and half of it is attached to the wall. Flatten the plaster with a little pressure to remove air bubbles and areas that are not perfectly gluey. Cover the plaster with paint to make it look neat. Use the colors that are matching with the color of roof tile and walls.
Repair the Carport Concrete Floor
Carport concrete floors are usually incapable to support the load properly, if the ground support power is not good or low. The floor can collapse after being used for some time. These problems often occur if the construction is not careful, so that the work floor or under-floor layer is not properly compacted and creates a gap. To fix this, follow the guidelines below.
Remove the collapsed carport floor, until the ground level can be seen. If there are cracks in other areas, it is better to thoroughly demolish the floor. Compact the collapsed soil using a leveling or stamping machine. Do it gradually, layer by layer as thick as 10 cm. In order for the carport base to be stronger and more stable, give a layer by spreading of hard rock with 20 cm diameter above the ground. Cover the stone layer using a layer of sirtu (stone sand). The sirtu thickness is 5 cm from the rock surface. Do it gradually, layer by layer as thick as 10 cm. In order for the carport base to be stronger and more stable, give a layer by spreading of hard rock with 20 cm diameter above the ground. Cover the stone layer using a layer of sirtu (stone sand). The sirtu thickness is 5 cm from the rock surface. Then, give a concrete casting on top of the sirtu layer using steel reinforcement with a diameter of 8 mm – 10 mm to make a strong result. Leave the carport floor that has been casted for 3 to 4 weeks before using it, for concrete maturation.
See also: Construction And Building Materials For Home Renovations That You Should Know
How about impression over? Is actually which awesome??? If you believe and so, I’l l demonstrate a few graphic all over again down below:
So, if you would like receive these awesome graphics related to 10 Tips and Tricks About House Renovation You Should Know, simply click save icon to save these shots to your personal pc. There’re all set for obtain, if you appreciate and want to take it, just click save logo in the web page, and it’ll be directly saved in your laptop computer.
Thanks for visiting raysahouse.com, content above 10 Tips and Tricks About House Renovation You Should Know published. Lots of people trying to find info about House Renovation and certainly one of them is you, is not it?